MSDS Sheet

MSDS

Interleaf Flap Wheel

Section I

Manufacturer's Name: Weiler Corporation
Address: One Weiler Drive, Cresco, PA 18326
Emergency Telephone Number: (570) 595-7495
Telephone Number for Information: (570) 595-7495
Date prepared: January 25, 2006
Name of preparer: Frank J. Hettes

Section II - Hazardous Ingredients / Identity Information

Hazardous Components, (Specific Chemical Identity, Common Name(s)	CAS#	OSHA PEL	ACGIH TL	Carcinogen (Y/N)	% (optional)
Flint Mineral (as quartz resp. dust)	14808-60-7	0.1 mg/m³	0.1 mg/m³	Y See note#	45-50%
Cured Adhesive	Unknown	None**	None**	None**	10-35%
Polyester Fiber	Unknown	None**	None**	None**	25-30%

#NOTE: While the following effects are associated with one or more of the individual ingredients
in this product and are required to be included on the MSDS by the U.S. OSHA Hazard
Communication Standard, they are not expected effects during foreseeable use of this product.

Contains a chemical that can cause cancer (14808-60-7). (NTP anticipated human carcinogen,
IARC probable human carcinogen, Calif. proposition 65).

Section III - Physical / Chemical Characteristics

Boiling Point: N/A*
Vapor Pressure (mm Hg.): N/A*
Vapor Density (AIR=1): N/A*
Percent Volatile by Volume: N/A*
Solubility in Alcohol: N/A*
Solubility in Water: N/A*
Solubility in Other Solvent: N/A*
Specific Gravity (H₂O=1): N/A*
Melting Point: N/A*
Evaporation Rate (Butyl Acetate=1): N/A*
Appearance and Odor: Non-woven Material

Section IV - Fire and Explosion Hazard Data

Flash Point (method used): N/A*
Flammable Limits: LEL: N/A* UEL: N/A*
Extinguishing Media: Water, carbon dioxide, dry chemical, foam
Special Fire Fighting Procedures: Wear full protective clothing including helmet, self-contained
positive pressure or pressure demand breathing apparatus, bunker coat and pants, bands
around arms, waist and legs, face mask, and protective covering for exposed areas of the head.
Unusual Fire and Explosion Hazards: N/A*
NFPA Hazard Codes: Health - 1, Fire - 0, Reactivity - 0, Unusual reaction hazard - none

Section V - Reactivity Data

Stability: Stable
Incompatibility (Materials to Avoid): N/A*
Hazardous Decomposition or Byproducts: No hazardous decomposition products are expected
during normal use of this product; however, during flaming conditions or excessive heating, the
following may be emitted: Carbon monoxide, carbon dioxide, oxides of nitrogen, cyanides,
formaldehyde.
Hazardous Polymerization: Will not occur

Section VI - Health Hazard Data

Primary Route(s) of Entry	Acute and chronic Health Effects and Effects of Overexposure	First Aid and Medical Information
Inhalation (during use)	Dust from cutting, grinding, sanding or machining may cause irritation of the respiratory system. While the following effects are associated with one or more of the individual ingredients in this product and are required to be included on the MSDS by the U.S. OSHA Hazard Communication Standard, they are not expected effects during foreseeable use of this product: Silicosis: Signs/symptoms can include shortness of breath and persistent coughing.	If signs/symptoms occur, remove person to fresh air. If signs/symptoms continue, call a physician.
Ingestion	No adverse health effects are expected from swallowing.	N/A*
Skin (contact & absorption)	No adverse health effects are expected from skin contact. Mechanical skin irritation: Signs/symptoms can include itching and redness.	Wash affected area with soap and water.
Eye	Eye contact is not expected to occur during normal use of the product. Mechanical eye irritation: Signs/symptoms can include irritation, redness, scratching of the cornea and tearing. Dust created by cutting, grinding, sanding or machining may cause eye irritation.	Immediately flush eyes with large amounts of water. Get immediate medical attention.
Other Potential Health Risks	This product, when used under reasonable conditions or in accordance with the directions for use should not present a health and safety hazard; however, use or processing of the product in a manner not in accordance with the product's directions for use may affect the performance of the product and may present potential health and safety hazards.	All first aid statements refer to exposure of dust created by cutting, sanding or grinding.

Section VII - Precautions For Safe Handling And Use

Normal Storage and Handling: N/A*
Normal Use: N/A*
Precautions to be Taken in Handling and Storage: N/A*
Steps to be Taken in Case Material is Released or Spilled: N/A*
Waste Disposal Method: Incinerate in an industrial or commercial facility.
Dispose of waste product in a sanitary landfill.

Section VIII - Control Measures

Respiratory protection (specify type): Avoid breathing dust created by cutting, sanding or grinding.
  Select one of the following NIOSH approved respirators based on airborne concentration of
contaminants and in accordance with OSHA regulations: Half-mask dust respirator, full-face
dust respirator.
Ventilation: Provide appropriate local exhaust for grinding, cutting or sanding cured material.
  Provide sufficient ventilation to maintain emissions below recommended exposure limits.
  If exhaust ventilation is not adequate, use appropriate respiratory protection.
Protective gloves: Recommended.
Eye protection: Wear safety glasses with side shields. Use protective glasses and/or face shield as
  recommended in ANSI Standard Z87.1.
Other protective clothing or equipment: N/A*

*N/A = Not Applicable

**None = None established

MSDS Interleaf Flap Wheel

MSDS

Interleaf Flap Wheel