MSDS

Trim-Kut Grinding Disc

(Aluminum Oxide Resin Nylon/Abs)

Section I

Manufacturer's name: Weiler Corporation
Address: One Weiler Drive, Cresco, PA 18326
Emergency telephone number: (570) 595-7495
Telephone number for information: (570) 595-7495
Date prepared: January 25, 2006
Name of preparer: Frank J. Hettes

Section II - Hazardous Ingredients / Identity Information

Note: Weiler Corporation regards these products as "articles" as defined in the Federal Occupational
Safety and Health Administration Hazard Communication Standard 29CFR1910.1200. The use of
approved respirators, ventilation equipment, face and hand protection is recommended for the safe
use of these products.

Definition of "Article" per 29CFR1910.1200 7/1/88 edition: "Article" means manufactured item:
(i) Which is formed to a specific shape or design during manufacture; (ii) Which has end use function(s)
dependent in whole or in part upon its shape or design during end use; and (iii) Which does not release,
or otherwise result in, exposure to a hazardous chemical, under normal conditions of use.

Section III - Physical / Chemical Characteristics

Boiling Point: *N/A
Vapor Pressure (mm Hg.): *N/A
Vapor Density (AIR=1): *N/A
Percent Volatile by Volume: *N/A
Solubility in Alcohol: *N/A
Specific Gravity (H₂O=1): *N/A
Melting Point: *N/A
Evaporation Rate (Butyl Acetate=1): *N/A
Solubility in Water: *N/A
Solubility in Other Solvent: *N/A
Appearance and Odor: Green backing; odorless

Section IV - Fire and Explosion Hazard Data

Flash Point (method used): *N/A
Flammable Limits: LEL: *N/A   UEL: *N/A
Extinguishing Media: Standard extinguishers or water
Special Fire Fighting Procedures: *N/A
Unusual Fire and Explosion Hazards: *N/A

Section V - Reactivity Data

Stability: Stable
Conditions to Avoid: During use, dust and grinding fumes are generated.
Note: The material being ground will generally create substantially greater amounts of air borne particles.

Incompatibility (Materials to Avoid): *N/A

Hazardous Decomposition or Byproducts: During use, dust and grinding fumes are generated.
Note: The material being ground will generally create substantially greater amounts of air borne particles.

Hazardous Polymerization: Will not occur.
Conditions to Avoid: None.

Section VI - Health Hazard Data

Section VII - Precautions For Safe Handling And Use

Normal storage and handling: Store in dry area away from heat source. Ideal storage 65-70 
degrees fahrenheit, 50-60% RH.

Normal use: Handle with adequate ventilation. See OSHA 29CFR1910.94 (Ventilation), 
OSHA 29CFR1910.1000 (Air Contaminates) and OSHA CFR1910.213(P) (Sanding Machines).

Precautions to be taken in handling and storage: Handle with adequate ventilation.
See OSHA 29CFR1910.94 (Ventilation) and OSHA 29CFR1910.1000 (Air Contaminates).

Steps to be taken in case material is released or spilled: Normal clean up procedures.

Waste disposal method: Standard landfill methods consistent with applicable Federal, 
  State and Local laws.

Section VIII - Control Measures

Respiratory protection (specify type): As needed, approved dust respirator OSHA 24CFR1910.134

Ventilation:
  Local exhaust: Recommended
  Mechanical (general): Recommended
  Other: No applicable information found

Protective gloves: Recommended

Eye protection: ANSI Standard Z87.1 and OSHA 29CFR1910.133 (Face & Eye Protection)

Other protective clothing or equipment: Protective clothing recommended to cover exposed skin.
Hearing protection recommended (see OSHA 29CFR1910.215 (Hearing Protection).

*N/A = Not applicable