MSDS

Unitized Wheel

Section I

Manufacturer's Name: Weiler Corporation
Address: One Weiler Drive, Cresco, PA 18326
Emergency Telephone Number: (570) 595-7495
Telephone Number for Information: (570) 595-7495
Date prepared: January 25, 2006
Name of preparer: Frank J. Hettes

Section II - Hazardous Ingredients / Identity Information

*Materials are regulated by OSHA 29CFR1910.1200 Hazard Communication Standard.

NOTE: Weiler Corporation regards these products as "articles" as defined in the Federal Occupational Safety and Health Administration Hazard Communication Standard 29CFR1910.1200. The use of approved respirators, ventilation equipment, face and hand protection is recommended for the safe use of these products.

Definition of "Article" per 29CFR1910.1200 7/1/88 edition: "Article" means manufactured item;
(i)Which is formed to a specific shape or design during manufacture; (ii)Which has end use function(s)
dependent in whole or in part upon its shape or design during end use; and (iii) Which does not release,
or otherwise result in exposure to a hazardous chemical, under normal conditions of use.

**The EPA has designated that non-fibrous forms of aluminum oxide are not a toxic chemical under
Section 313 of SARA.

Section III - Physical / Chemical Characteristics

Boiling Point: N/A
Vapor Pressure (mm Hg.): N/A
Vapor Density (AIR=1): N/A
Percent Volatile by Volume: N/A
Solubility in Water: N/A
Solubility in Alcohol: N/A
Solubility in Other Solvent: N/A
Specific Gravity (H₂O=1): N/A
Melting Point: N/A
Evaporation Rate (Butyl Acetate=1): N/A
Appearance and Odor: Wheel impregnated with abrasive material

Section IV - Fire and Explosion Hazard Data

Flash Point (method used): N/A
Flammable Limits: N/A   LEL: N/A   UEL: N/A
Extinguishing Media: N/A
Special Fire Fighting Procedures: Backings and resin binder will burn or decompose,
  use respiratory protection.
Unusual Fire and Explosion Hazards: N/A

Section V - Reactivity Data

Stability: Stable
Incompatibility (Materials to Avoid): N/A
Hazardous Decomposition or Byproducts: In-use dust and decomposing resin system fumes are
  generated. In most cases, the material removed from the work piece will be significantly greater
  than the abrasive product components.
Hazardous Polymerization: Will not occur.

Section VI - Health Hazard Data

Section VII - Precautions For Safe Handling And Use

Normal storage and handling: Handle with adequate ventilation. See OSHA 29CFR1910.94 
  (Ventialtion) and OSHA 29CFR1910.1000 (Air Contaminates).
Normal use: Handle with adequate ventilation. See OSHA 29CFR1910.94 (Ventialtion),
  OSHA 29CFR1910.1000 (Air Contaminates) and OSHA CFR1910.213(P) (Sanding Machines).
Steps to be taken in case material is released or spilled: Normal clean up procedures.
Waste disposal method: Standard landfill methods consistent with applicable Federal, 
  State and Local laws.
Precautions to be taken in handling and storage: N/A

Section VIII - Control Measures

Respiratory protection (specify type): As needed, approved dust respirator 
  (OSHA 24CFR1910.134)
Ventilation:
  Local Exhaust: Recommended
  Mechanical (General): Recommended
  Other: No applicable information found
Protective gloves: As desired by user
Eye protection: Recommended OSHA 29CFR1910.133 (Face & Eye Protection)
Other protective clothing or equipment: As needed, hearing protection OSHA 29CFR1910.215
  (Hearing Protection)

N/A = Not Applicable